岗位职责:
2.0Job Summary 职位概述
Take full responsibility of Software development for automobile controllers, including technical development trend, requirements analysis from customer, Software architecture design, basic software development, application software development and software test, etc.
负责汽车控制器的软件开发，包括技术发展趋势、客户需求分析、软件架构设计、基础软件开发、应用软件开发和软件测试等。
3.0Key Responsibilities 主要职责
Responsible for software design of automotive thermal management controller, OBW (On-board weight) controller, cleaning system controller and valve actuator.
负责汽车热管理控制器、OBW（车载重量）控制器、清洗系统控制器和阀门执行器的软件设计。
Responsible for software requirement analyzing and software architecture design.
负责软件需求分析和软件架构设计。
Responsible for basic software requirement analysis and basic software design.
负责底层软件需求分析和底层软件设计。
Responsible for the software development of RTE.
负责应用层与底层接口开发。
Responsible for the development of upper communication GUI host by C# or other language.
负责用C#或其他语言开发上层通信GUI主机。
Responsible for software technical problem solving.
负责软件技术问题的解决。
Participate in the construction of software development related processes, tool chains and databases, and coordinate internally and externally.
参与软件开发相关流程、工具链和数据库的建设，并进行内部和外部协调。
Responsible for complete software-level testing(HIL,MIL etc.).
负责完成软件级测试（HIL、MIL等）。
任职要求:
4.0Required education, experience, knowledge and skills 需要的教育、经验、知识及技能
Education: Master degree or above, more than 5 years working software development experience in automotive industry .
学历：硕士及以上学历，5年以上汽车行业软件开发工作经验。
Major: Electrical Engineering, Electronic Science and Technology, computer, software, communication and related majors.
专业：电气工程、电子科学与技术、计算机、软件、通信及相关专业。
Know well about C programming language, familiar with Bootloader development used in embedded code development.
熟悉C编程语言，熟悉嵌入式代码开发中使用的Bootloader开发。
Skilled use of mainstream automotive MCU, like TI, NXP, ST, etc.
熟练使用TI、NXP、ST等主流汽车MCU。
Know well about vehicle network communication and related standards like LIN/CAN/CANFD/J1939. Better if know FlexRay/ETHERNET&LIN2.2/100BASE-T1/ISO 11898 , etc.
熟悉车辆网络通信和LIN/CAN/CANFD/J1939等相关标准。了解FlexRay/ETHERNET和LIN2.2/100BASE-T/ISO 11898等。
Know well about the basic bottom signal requirements used in motor and solenoid valve control.
熟悉电机和电磁阀控制中使用的基本底层信号要求。
Experience in diagnosis development based on UDS, know well about ISO15765 ISO14229 and DoIP.
基于UDS的诊断开发经验，熟悉ISO15765、ISO14229和DoIP。
Experience in function safety development, familiar with ISO26262 and ASPICE.
有功能安全开发经验，熟悉ISO26262和ASPICE。
Experience in OTA development and related standards.
有OTA开发和相关标准的经验。
Experience in signal filtering algorithm.
有信号滤波算法经验。
Experience in calibration development based on XCP/CCP.
基于XCP/CCP的校准开发经验。
Familiar with Autosar standard, proficient in a tool chain like Vector or ETAS is preferred.
熟悉Autosar标准，精通Vector或ETAS等工具链者优先。
Personality: responsible, enterprising, strong sense of teamwork, self-driven, and problem-solving mindset
性格：负责、进取、团队合作意识强、自我驱动、解决问题的心态
Excellent communication skills in English and Mandarin both written and verbal.
优秀的英语和普通话书面和口头沟通技巧。